Error Messages and Descriptions Each message that appears in the event log has an error level that indicates the severity of the event, as shown in the following table. Table 11. Error Messages and Descriptions Number Event Text 0x00 Command completed successfully 0x01 Invalid command 0x02 DCMD Opcode is invalid 0x03 Input parameters are invalid 0x04 Invalid sequence number 0x05 Abort is not possible for the requested command 0x06 Application host code not found 0x07 Application already in use - try later 0x08 Application not initialized 0x09 Given array index is invalid 0x0a Unable to add missing drive to array, as row has no empty slots 0x0b Some of the CFG resources conflict with each other or the current configuration 0x0c Invalid device ID/select-timeout 0x0d Drive is too small for requested operation 0x0e Flash memory allocation failed 0x0f Flash download already in progress 0x10 Flash operation failed 0x11 Flash image was bad 0x12 Downloaded Flash image is incomplete 0x13 Flash OPEN was not done 0x14 Flash sequence is not active 0x15 Flush command failed 0x16 Specified application does not have host-resident code 0x17 LD operation not possible - CC is in progress 0x18 LD initialization in progress 0x19 LBA is out of range 0x1a Maximum LDs are already configured 0x1b LD is not OPTIMAL 0x1c LD Rebuild is in progress 0x1d LD is undergoing reconstruction 0x1e LD RAID level is wrong for requested operation 0x1f Too many spares assigned 0x20 Scratch memory not available - try command again later 0x21 Error writing MFC data to SEEPROM 0x22 SuperCap is missing Do not hot plug the SuperCap when power is supplied to the controller or if there is residual charge on the SuperCap, doing so might damage both the SuperCap and the controller unit. 0x23 Item not found 0x25 PD CLEAR operation is in progress 0x27 Patrol Read is disabled 0x28 Given row index is invalid 0x2e I/O request for MFI_CMD_OP_PD_SCSI failed 0x2f Matches SCSI RESERVATION_CONFLICT 0x30 One or more of the flush operations failed 0x31 Firmware real-time currently not set 0x32 Command issues while firmware in wrong state (that is, GET RECON when op not active) 0x33 LD is not OFFLINE - I/O not possible 0x34 Peer controller rejected request (possibly due to resource conflict) 0x35 Unable to inform peer of communication changes (retry might be appropriate) 0x36 LD reservation already in progress 0x37 I2C errors were detected 0x38 PCI errors occurred during XOR/DMA operation 0x39 Diagnostics failed - see event log for details 0x3a Unable to process command as boot messages are pending 0x3b Returned in case if foreign configurations are incomplete 0x3d Returned in case if a command is tried on unsupported hardware 0x3e CC scheduling is disabled 0x3f PD CopyBack operation is in progress 0x40 Selected more than one PD per array 0x41 Microcode update operation failed 0x42 Unable to process command as drive security feature is not enabled 0x43 Controller already has a lock key 0x44 Lock key cannot be backed-up 0x45 Lock key backup cannot be verified 0x46 Lock key from backup failed verification 0x47 Rekey operation not allowed, unless controller already has a lock key 0x48 Lock key is not valid, cannot authenticate 0x49 Lock key from escrow cannot be used 0x4a Lock key backup (pass-phrase) is required 0x4b Secure LD exist 0x4c LD secure operation is not allowed 0x4d Reprovisioning is not allowed 0x4e Drive security type (FDE or non-FDE) is not appropriate for requested operation 0x4f LD encryption type is not supported 0x50 Cannot mix FDE and non-FDE drives in same array 0x51 Cannot mix secure and unsecured LD in same array 0x53 Physical device errors were detected 0x54 Controller has LD cache pinned 0x55 Requested operation is already in progress 0x56 Another power state set operation is in progress 0x57 Power state of device is not correct 0x58 No PD is available for patrol read 0x59 Controller reset is required 0x5c For consistency SET PiTs, some PiT creations might fail or succeed 0xFF Invalid status - used for polling command completion
Error Messages and Descriptions
Each message that appears in the event log has an error level that indicates the severity of the event, as shown in the following table.
Table 11. Error Messages and Descriptions
Number
Event Text
0x00
Command completed successfully
0x01
Invalid command
0x02
DCMD Opcode is invalid
0x03
Input parameters are invalid
0x04
Invalid sequence number
0x05
Abort is not possible for the requested command
0x06
Application host code not found
0x07
Application already in use - try later
0x08
Application not initialized
0x09
Given array index is invalid
0x0a
Unable to add missing drive to array, as row has no empty slots
0x0b
Some of the CFG resources conflict with each other or the current configuration
0x0c
Invalid device ID/select-timeout
0x0d
Drive is too small for requested operation
0x0e
Flash memory allocation failed
0x0f
Flash download already in progress
0x10
Flash operation failed
0x11
Flash image was bad
0x12
Downloaded Flash image is incomplete
0x13
Flash OPEN was not done
0x14
Flash sequence is not active
0x15
Flush command failed
0x16
Specified application does not have host-resident code
0x17
LD operation not possible - CC is in progress
0x18
LD initialization in progress
0x19
LBA is out of range
0x1a
Maximum LDs are already configured
0x1b
LD is not OPTIMAL
0x1c
LD Rebuild is in progress
0x1d
LD is undergoing reconstruction
0x1e
LD RAID level is wrong for requested operation
0x1f
Too many spares assigned
0x20
Scratch memory not available - try command again later
0x21
Error writing MFC data to SEEPROM
0x22
SuperCap is missing
Do not hot plug the SuperCap when power is supplied to the controller or if there is residual charge on the SuperCap, doing so might damage both the SuperCap and the controller unit.
0x23
Item not found
0x25
PD CLEAR operation is in progress
0x27
Patrol Read is disabled
0x28
Given row index is invalid
0x2e
I/O request for MFI_CMD_OP_PD_SCSI failed
0x2f
Matches SCSI RESERVATION_CONFLICT
0x30
One or more of the flush operations failed
0x31
Firmware real-time currently not set
0x32
Command issues while firmware in wrong state (that is, GET RECON when op not active)
0x33
LD is not OFFLINE - I/O not possible
0x34
Peer controller rejected request (possibly due to resource conflict)
0x35
Unable to inform peer of communication changes (retry might be appropriate)
0x36
LD reservation already in progress
0x37
I2C errors were detected
0x38
PCI errors occurred during XOR/DMA operation
0x39
Diagnostics failed - see event log for details
0x3a
Unable to process command as boot messages are pending
0x3b
Returned in case if foreign configurations are incomplete
0x3d
Returned in case if a command is tried on unsupported hardware
0x3e
CC scheduling is disabled
0x3f
PD CopyBack operation is in progress
0x40
Selected more than one PD per array
0x41
Microcode update operation failed
0x42
Unable to process command as drive security feature is not enabled
0x43
Controller already has a lock key
0x44
Lock key cannot be backed-up
0x45
Lock key backup cannot be verified
0x46
Lock key from backup failed verification
0x47
Rekey operation not allowed, unless controller already has a lock key
0x48
Lock key is not valid, cannot authenticate
0x49
Lock key from escrow cannot be used
0x4a
Lock key backup (pass-phrase) is required
0x4b
Secure LD exist
0x4c
LD secure operation is not allowed
0x4d
Reprovisioning is not allowed
0x4e
Drive security type (FDE or non-FDE) is not appropriate for requested operation
0x4f
LD encryption type is not supported
0x50
Cannot mix FDE and non-FDE drives in same array
0x51
Cannot mix secure and unsecured LD in same array
0x53
Physical device errors were detected
0x54
Controller has LD cache pinned
0x55
Requested operation is already in progress
0x56
Another power state set operation is in progress
0x57
Power state of device is not correct
0x58
No PD is available for patrol read
0x59
Controller reset is required
0x5c
For consistency SET PiTs, some PiT creations might fail or succeed
0xFF
Invalid status - used for polling command completion