| Top |
NMSettingInfinibandNMSettingInfiniband — Describes connection properties for IP-over-InfiniBand networks |
| GQuark | nm_setting_infiniband_error_quark () |
| NMSetting * | nm_setting_infiniband_new () |
| const GByteArray * | nm_setting_infiniband_get_mac_address () |
| guint32 | nm_setting_infiniband_get_mtu () |
| const char * | nm_setting_infiniband_get_transport_mode () |
| int | nm_setting_infiniband_get_p_key () |
| const char * | nm_setting_infiniband_get_parent () |
| GArray_guchar_ * | mac-address | Read / Write |
| guint | mtu | Read / Write / Construct |
| gint | p-key | Read / Write / Construct |
| gchar * | parent | Read / Write / Construct |
| gchar * | transport-mode | Read / Write / Construct |
| #define | NM_SETTING_INFINIBAND_SETTING_NAME |
| enum | NMSettingInfinibandError |
| #define | NM_SETTING_INFINIBAND_ERROR |
| #define | NM_SETTING_INFINIBAND_MAC_ADDRESS |
| #define | NM_SETTING_INFINIBAND_MTU |
| #define | NM_SETTING_INFINIBAND_TRANSPORT_MODE |
| #define | NM_SETTING_INFINIBAND_P_KEY |
| #define | NM_SETTING_INFINIBAND_PARENT |
The NMSettingInfiniband object is a NMSetting subclass that describes properties necessary for connection to IP-over-InfiniBand networks.
GQuark
nm_setting_infiniband_error_quark (void);
Registers an error quark for NMSettingInfiniband if necessary.
NMSetting *
nm_setting_infiniband_new (void);
Creates a new NMSettingInfiniband object with default values.
const GByteArray *
nm_setting_infiniband_get_mac_address (NMSettingInfiniband *setting);
guint32
nm_setting_infiniband_get_mtu (NMSettingInfiniband *setting);
const char *
nm_setting_infiniband_get_transport_mode
(NMSettingInfiniband *setting);
Returns the transport mode for this device. Either 'datagram' or 'connected'.
int
nm_setting_infiniband_get_p_key (NMSettingInfiniband *setting);
Returns the P_Key to use for this device. A value of -1 means to use the default P_Key (aka "the P_Key at index 0"). Otherwise it is a 16-bit unsigned integer.
const char *
nm_setting_infiniband_get_parent (NMSettingInfiniband *setting);
Returns the parent interface name for this device, if set.
#define NM_SETTING_INFINIBAND_ERROR nm_setting_infiniband_error_quark ()
“mac-address” property “mac-address” GArray_guchar_ *
If specified, this connection will only apply to the IPoIB device whose permanent MAC address matches. This property does not change the MAC address of the device (i.e. MAC spoofing).
Owner: NMSettingInfiniband
Flags: Read / Write
“mtu” property“mtu” guint
If non-zero, only transmit packets of the specified size or smaller, breaking larger packets up into multiple frames.
Owner: NMSettingInfiniband
Flags: Read / Write / Construct
Default value: 0
“p-key” property“p-key” gint
The InfiniBand P_Key to use for this device. A value of -1 means to use the default P_Key (aka "the P_Key at index 0"). Otherwise it is a 16-bit unsigned integer, whose high bit is set if it is a "full membership" P_Key.
Owner: NMSettingInfiniband
Flags: Read / Write / Construct
Allowed values: [-1,65535]
Default value: -1
“parent” property“parent” gchar *
The interface name of the parent device of this device. Normally NULL,
but if the “p_key” property is set, then you must
specify the base device by setting either this property or
“mac-address”.
Owner: NMSettingInfiniband
Flags: Read / Write / Construct
Default value: NULL
“transport-mode” property“transport-mode” gchar *
The IP-over-InfiniBand transport mode. Either "datagram" or "connected".
Owner: NMSettingInfiniband
Flags: Read / Write / Construct
Default value: NULL